اختبار مقاومة الحريق للطلاءات الفولاذية المقاومة للحريق: من اختبار الفرن إلى جدول السماكة

الجواب القصير

Fire resistance testing for steel fireproof coatings is a furnace test that measures steel temperature, not coating performance. A coated steel beam or column is heated to the ايزو 834-1 منحنى 4 under في 1363-1 5, and the steel temperature is recorded until it reaches the critical temperature used for the design. Two European methods make this work: في 13381-4 for applied passive protection (لوحات, renders, sprayed systems) 1 و في 13381-8 for applied reactive protection (intumescent coatings) 2, both listed as the 2013 editions [1][2]. The output is not a pass mark but an assessment report converting furnace data into a minimum thickness schedule per section factor and R-rating, classified under في 13501-2 6. The question is never “is this coating fire resistant” but “for which section factor, which R-rating and which standard does this thickness schedule hold”.

What Fire Resistance Testing for Steel Fireproof Coatings Actually Measures

The Curve That Drives the Test

The exposure is not a flame but a prescribed temperature history. The generic requirements live in في 1363-1:2020 [5]; the curve itself in ايزو 834-1:2025 [4]. It is the familiar logarithmic rise: gas temperature reaches roughly 842 درجة مئوية عند 30 دقائق, 945 درجة مئوية عند 60 دقائق, 1,006 درجة مئوية عند 90 دقائق و 1,049 درجة مئوية عند 120 دقائق. That is gas temperature in the furnace, not the protected steel — the steel always lags behind, and how far behind is the whole point of the test.

The Recorded Quantities

What the coating test measures is the temperature reached by the protected steel section و, in many assessments, the unheated side of the assembly.

The Critical Steel Temperature

ال critical steel temperature is the design input that turns temperatures into a rating. It is not a constant fixed by the test standard: it comes from the structural fire design of the member under الرمز الأوروبي 3, جزء 1-2, whose current edition is في 1993-1-2:2024, in force since 20 March 2024 3. That version change is worth catching — the previous 2005 edition is shown as withdrawn on the same date, so a report still citing “في 1993-1-2:2005” works from a superseded document.

The coating is a system, not a film: the specimen includes substrate preparation, primer, coating at a defined dry film thickness, steel grade and section, and the fixing and joint detail. A datasheet describes the product; a test report describes an assembly.

Two Standards for Fire Resistance Testing for Steel Fireproof Coatings

The word “fireproof coating” hides a distinction that decides which standard applies. A coating either does something to the fire (reactive: it intumesces, chars and insulates) أو does something to the steel (passive: it adds mass and board protection that delays heating). في 13381-4 و إن 13381-8 were written for these two behaviours separately, and a test report under one of them says nothing about the other [1][2].

في 13381-4: Applied Passive Protection

جزء 4 covers protection systems that delay the heating of the steel — boards, cementitious renders, sprayed systems and similar layers. Its title is explicit about the boundary: test methods for determining the contribution to the fire resistance of structural members, applied passive protection to steel members [1]. It was listed in force on 1 May 2013 [1], and older project files often reference pre-2013 national editions, so an audit should start by confirming which edition the assessment report was written against.

في 13381-8: Applied Reactive Protection

جزء 8 covers reactive systems — intumescent and expandable coatings whose protective action is triggered by heat. The scope wording mirrors Part 4 with the protection type changed to applied reactive protection [2], with the same in-force date of 1 May 2013 [2].

Scope Limits That Belong in the Specification

Both parts carry the same structural limitation, and it belongs in a written specification: the method covers sections without openings in the web, and it is not directly applicable to structural tension members without further evaluation [1][2]. A lattice column with web holes, a tension bracing member or a heavily penetrated column therefore sits outside the direct scope of both methods — a report claiming “في 13381-8 certified” does not by itself cover that member.

From Furnace Data to a Thickness Schedule

The commercial output of a coating fire test is a table, not a certificate of “fire resistance”. The route from furnace data to a usable document runs through four steps, and each step is where a specification can go wrong.

How the Thickness Schedule Is Derived

1. Furnace testing of coated sections. A set of sections with different section factors and different coating thicknesses is tested under the ISO 834-1 منحنى [4].
2. Calculation of the unprotected reference. The same section geometry is assessed without protection, giving the baseline heating rate.
3. Derivation of the thickness schedule. The protected section is matched to the unprotected section with a safety margin, producing the minimum coating thickness for a given section factor and fire resistance duration.
4. Classification and extension. The assembly is classified under في 13501-2:2023 [6], and the assessment report may extend the tested results to other section factors, spans and thicknesses within defined limits.

Why Section Factor Decides Everything

ال section factor is the exposed perimeter divided by the cross-sectional area, and it governs how fast a section heats: a slender hollow section with a large perimeter-to-area ratio heats faster than a compact solid section, so it needs a thicker coating for the same duration. That is the parameter an extended-application assessment manipulates — and the reason a coating that passed on one profile may not be usable on another.

A specification saying “apply X mm of coating for R 60” without naming the section factor, steel grade, span and standard is incomplete in a way no laboratory can fix later, because those are the inputs the thickness was derived from. The thickness is not a catalogue constant either: it is a function of geometry and duration, which is why published tables are indexed by section factor and R-rating rather than a single number.

Intumescent Coatings Add Their Own Variable

A reactive coating does not protect the steel by mass; it protects it by chemistry, so the assessment must capture the reaction, not just the end point. The system is tested as supplied, including any primer, because primer and coating can interact.

Ageing, Primers and Site Application

Environmental ageing matters for the same reason: the assessment states which conditioning the thickness schedule is valid for, and a schedule quoted without its conditioning basis is not a complete document.

For readers who want the underlying strategy of protecting steel first, the article on اختبار مقاومة الحريق للهياكل الفولاذية sets out the three protection routes and the assessment report in broader context. For the product question — what a coating does versus what a fire-resistant board does — see fire retardant coating vs fire resistant coating.

The North American Route for Steel Fireproof Coatings

Outside Europe the same logic runs through two ASTM methods. ASTM E119 covers fire tests of building construction and materials and remains the reference method for time-temperature exposure and hose-stream testing of building elements 7. For structures exposed to large hydrocarbon pool fires — refinery platforms, petrochemical plant, offshore installations — ASTM E1529 provides the standard test methods for determining the effects of such fires on structural members and assemblies, with its own exposure definition based on the total flux incident on the specimen 8.

Why the Exposure Decides the Coating

The two routes ask different questions of the same product. A cellulosic curve is a slow, sustained exposure; a hydrocarbon pool fire is fast and intense. A coating assessed only against a building curve is not thereby assessed against a hydrocarbon exposure, and an oil-and-gas project that specifies “fire resistant coating” without naming the exposure has not made the testable part of the requirement.

Equipment for Fire Resistance Testing of Steel Fireproof Coatings

Buying the apparatus is the last step, but the specification drives it: a furnace with enough volume and control for the standard curve, thermocouple instrumentation positioned on the steel, a defined specimen support, and a measurement system that logs against the curve rather than against a stopwatch.

What to Check Before You Buy

A furnace intended for a coating test is also a furnace for coated steel members generally, which is why the equipment question overlaps with the wider fire resistance test furnace discussion.

Ask for the qualification package first: temperature uniformity verification over the working volume, the calibration certificate of the measurement chain, and a sample report from a real coated-section test. Fire resistance testing for steel fireproof coatings is only as good as that qualification chain. ال fire retardant coating test furnace page covers the configuration options.

الأسئلة المتداولة

Which standard is used to test fireproof coatings on steel?

Two European standards cover applied protection to steel members. في 13381-4 covers applied passive protection such as boards, renders and sprayed systems, و إن 13381-8 covers applied reactive protection such as intumescent coatings. Both are the 2013 editions, and both are run with the ISO 834-1 temperature-time curve under the general requirements of EN 1363-1.

What does a coating fire resistance test actually measure?

It measures the temperature reached by the protected steel. Thermocouples on the section log how fast the steel heats under the ISO 834-1 منحنى, and the result is the time needed to reach the critical steel temperature specified for the member. The coating itself is judged by what it does to that steel temperature, not by a separate coating test.

What is the critical steel temperature and where does it come from?

It is the temperature at which the steel section is assumed to have lost its fire resistance. It is not set by the coating test standard; it is derived from the structural fire design of the member under Eurocode 3 جزء 1-2, whose current edition is EN 1993-1-2:2024, in force since 20 March 2024. Using a critical temperature from the withdrawn 2005 edition can produce an assessment that no longer matches the code.

هل EN 13381-8 report cover any steel section?

لا. The test method covers steel members used as beams or columns and considers only sections without openings in the web. It is not directly applicable to structural tension members without further evaluation, so a perforated web, a lattice member or a heavily penetrated column needs a specific engineering justification that the coating report does not provide.

How is a coating thickness schedule produced?

A set of sections with different section factors and thicknesses is tested under the standard curve, an unprotected reference is calculated for the same geometry, and the results are matched with a safety margin to give a minimum thickness for each section factor and fire resistance duration. The assessment report then states the conditions under which that schedule may be extended to other geometries.

Can a coating tested to the building curve be used on an oil and gas structure?

Not on that evidence alone. A building curve is a slow, sustained exposure, while a large hydrocarbon pool fire is fast and intense. ASTM E1529 provides the methods for the hydrocarbon case, and a coating assessed under EN 13381 alone has not been assessed against that exposure.

How is a coated steel member verified on site?

By dry film thickness measurements against the approved thickness schedule, plus inspection of surface condition, preparation and continuity. The coating product, primer, substrate steel grade and thickness all form part of the tested assembly, so any substitution on site invalidates the assessment on which the schedule was based.

خاتمة: أمر القرار

1. Fix the exposure and the standard first: ايزو 834-1 تحت EN 1363-1 for building elements, ASTM E119 for the North American route, ASTM E1529 for hydrocarbon pool fires.
2. Choose the test method by protection type: في 13381-4 for passive protection, في 13381-8 for reactive protection [1][2].
3. Take the critical steel temperature from the current code, في 1993-1-2:2024, not from a pre-2024 document [3].
4. Ask for the assessment report with the thickness schedule, the section factors covered, the conditioning basis and the extension rules.
5. Then buy the apparatus: a furnace with verified uniformity, proper thermocouple instrumentation and a data system that logs to the curve.

Run this order once per project and fire resistance testing for steel fireproof coatings stops being a vague promise of “fire protection” and becomes a document trail: an exposure, a standard, a critical temperature, a thickness schedule with named section factors, and a furnace capable of reproducing it. The two posts worth reading next are اختبار مقاومة الحريق للهياكل الفولاذية for the protection strategy and fire retardant coating vs fire resistant coating for the product classification that decides which method applies. For equipment, انظر فرن اختبار الطلاء المقاوم للحريق و فرن اختبار مقاومة الحريق الأفقي الصفحات; send BRT your section sizes and R-rating target and we will map the package.

عن المؤلف

اختبار النقل السريع للحافلات (Shenyang Baoruitong Automation Equipment) manufactures steel fire protection and fire resistance test equipment — coating test furnaces, vertical and horizontal resistance furnaces, and the instrumentation that runs the standard curves. The content team writes for fabricators, coating manufacturers and laboratory buyers, with the standard editions cited above verified against the UNI catalogue, the ASTM store and the ISO/IEC webstore in November 2026.

مصادر

1. UNI—EN 13381-4:2013, Test methods for determining the contribution to the fire resistance of structural members — Part 4: Applied passive protection to steel members (in force 01 May 2013). https://webstore.uni.com/en/en-13381-4-2013
2. UNI—EN 13381-8:2013, Test methods for determining the contribution to the fire resistance of structural members — Part 8: Applied reactive protection to steel members (in force 01 May 2013). https://webstore.uni.com/en/en-13381-8-2013
3. UNI—EN 1993-1-2:2024, الرمز الأوروبي 3 — Design of steel structures — Part 1-2: Structural fire design (in force 20 March 2024; ال 2005 edition is shown as withdrawn on the same date). https://webstore.uni.com/en/en-1993-1-2-2024
4. النوم - كبير 834-1:2025, Fire-resistance tests — Elements of building construction — Part 1: General requirements (in force 30 May 2025). https://webstore.uni.com/en/iso-834-1-2025
5. UNI—EN 1363-1:2020, Fire resistance tests — Part 1: General requirements (in force 19 February 2020). https://webstore.uni.com/en/en-1363-1-2020
6. UNI—EN 13501-2:2023, Fire classification of construction products and building elements — Part 2: Classification using data from fire resistance and/or smoke control tests (in force 31 May 2023). https://webstore.uni.com/en/en-13501-2-2023
7. ASTM — E119, طرق الاختبار القياسية لاختبارات الحريق في تشييد المباني والمواد. https://store.astm.org/e119.html
8. ASTM — E1529, Standard Test Methods for Determining Effects of Large Hydrocarbon Pool Fires on Structural Members and Assemblies. https://store.astm.org/e1529.html